DWS SystemsDimensioning System OverviewStatic DWSDynamic DWSDWS MachineDesktop DimensionerPackage DimensionerPallet DimensionerFreight DimensionerPallet Measuring SystemTruck DimensioningScanning TunnelWeigh-in-MotionVolumetric ScannerDimensioner RangeCubing SystemSortersSortation System OverviewCross Belt SorterLinear Cross-Belt SorterLoop Cross-Belt SorterWheel SorterNarrow Belt SorterParcel SorterSingulatorConveyorsConveyor SystemsBelt ConveyorRoller ConveyorIncline & Curve ConveyorTelescopic ConveyorGuidesWhat Is DWS?Dimensional Weight ExplainedDim Weight CalculatorHow to Calculate Dimensional WeightMobile vs Fixed DimensioningWarehouse DimensioningLogistics SortingAutomationBlogAboutContact / Get a QuoteEnglishEspañolFrançaisPortuguêsРусский
DWG DWS-03 · AUTOMATED DIMENSIONING

Automated dimensioning: measurement at line speed

Automated dimensioning removes the operator from the measuring loop. Parcels are singulated onto a belt, measured, weighed and scanned in motion, and routed onward — every item captured, no bench, no stopping, no sampling.

Request a DWS QuotationTry the Dim Weight Calculator
CAMERA / LIGHT CURTAIN IN MOTION DATA OUT L H DYNAMIC WEIGHING SECTION UNDER BELT
SCHEMATIC — STRUCTURE ILLUSTRATION, NOT TO SCALE

01What changes when dimensioning is automated

Manual and static dimensioning measure the parcels an operator has time to place on the machine. Automated dimensioning measures all of them. That difference matters commercially: carrier corrections are not evenly spread — they concentrate on exactly the oversize, irregular and badly labelled parcels that a sampling workflow misses. When every parcel carries your own dimension and weight record, the dispute conversation changes completely.

It also changes the labour maths. The measuring point stops being a workstation that needs staffing per shift and becomes a section of line that runs whenever the line runs, at the speed the sorter behind it demands.

02The automated measuring section, step by step

An automated dimensioning section in a Goodscan line is built from the dynamic end of the range:

  • Singulation first. A singulator takes bulk-fed parcels and delivers them single file with gaps — in-motion measurement and reading both depend on that spacing.
  • Dimensioning in motion. The GM210 and GS210M dynamic DWS machines capture length, width and height as the parcel crosses the measuring zone — by light curtain on the GM210Pro, by 3D vision on the GS210M.
  • Weighing in motion. A dynamic weigh section under the belt records weight without stopping the parcel, synchronised with the dimension capture.
  • Scanning at speed. Top reading for well-labelled flows, or a six-sided scanning tunnel where labels land anywhere — the code joins the record in the same pass.
  • Decision and routing. The completed record drives the sorter downstream and is stored for billing, audit and planning.
Throughput is set by the line design — belt speed, parcel spacing and the sorter behind the measuring section — rather than by any single machine. Lines are sized from your peak-hour profile during configuration, not from a headline number.

03Where automated dimensioning earns most

Express and e-commerce hubs are the classic fit: thousands of parcels per hour, carrier billing on every one, and sortation decisions that need dimensions for load planning. 3PL operations use automated dimensioning as a billing instrument — every client's parcel measured on induction, so storage and fulfilment charges run on records, not estimates. Returns centres use it in reverse: the same capture grades incoming parcels for re-stock, re-pack or disposal routing.

If your volume is below the point where a belt line makes sense, the same data discipline still applies at bench scale — see the parcel dimensioner range and the blog comparison of static and dynamic DWS.

FAQQuestions buyers ask

Does automated dimensioning need perfectly spaced parcels?
It needs gapped single file, which is what the singulator delivers. Parcels that touch or overlap are the main cause of missed captures on any in-motion system, so singulation is engineered as part of the section, not an accessory.
What happens to a parcel whose barcode cannot be read?
The line flags it: the parcel is routed to an exception position with its dimensions and weight already captured, so an operator only has to resolve the identity, not re-measure.
Can automated dimensioning feed our billing directly?
The per-parcel record — dimensions, weight, dimensional weight under your divisor, timestamp — is produced for exactly that purpose. The hand-off format to your systems is defined during project configuration.

Related equipment

Dynamic DWSThe machines at the core of the sectionSingulatorSingle-file feeding for measurementDimensioning SystemThe full measured line

Tell us what you measure — we size the system to it

Send your parcel or pallet size range, daily volume and destination layout. We reply with a configuration and quotation for the DWS line that fits, or call the service hotline 17376826899.

Request a DWS Quotation